WHDTS D2-5 Smart Car Soldering Project Kits Robotics for Kids DIY Electronics Education School Competition

0

Download the material from drive.google.com/open?id=1kLlV2NlXQeXo56ItreQ1JlUParTRc-16 1>.Install circuit 1.1 Install metal film resistor,DIP-8P IC socket,Self-Locking switch,Potentiometer,S8550, Capacitor, Red LED on PCB according to mark on PCB 1.2 Install Mecanum wheel The support bolts of the caster are inserted into the hole, tighten the nuts screwed into the caster, and finally fit the caster and tighten. 1.3

Categories: Kids Electronics

$11.99Amazon.com Price
(as of June 14, 2018 11:21 am GMT+0000 - Details)

Added on: June 14, 2018 - More: Comments & Reviews


Product Description


Download the material from drive.google.com/open?id=1kLlV2NlXQeXo56ItreQ1JlUParTRc-16

1>.Install circuit

1.1 Install metal film resistor,DIP-8P IC socket,Self-Locking switch,Potentiometer,S8550, Capacitor, Red LED on PCB according to mark on PCB

1.2 Install Mecanum wheel

The support bolts of the caster are inserted into the hole, tighten the nuts screwed into the caster, and finally fit the caster and tighten.

1.3 Install photoresistor and white LED on PCB reverse

1.4 Install battery case

1.5 Testing

Install 2pcs AA battery

Press on switch.If 2pcs white LED ON,the installation is successful.If LED off,please check the welding.

2>.Install mechanical parts

2.1 Install the four gaskets on the circuit board

2.2 Insert a steel shaft from the center hole of the wheel and note that the direction is inserted from one side of the raised sleeve of the wheel. It is better to insert the steel shaft parallel to the smooth side of the wheel

2.3 Put a three-way sleeve into the steel shaft, close to the wheel, and then a gasket into the steel shaft, close to the three-way sleeve, installed in place, toggle three-way sleeve, should be flexible. 

2.4 Place a gear into the steel shaft in the center of the steel shaft

2.5 Put a three-axis sleeve into the end of the steel shaft so that the car side of the wheel assembly to complete

2.6 Install Motor

3>. Testing

  3.1 Power on.Check S8550 or 10ohm resistor if motor don’t move

  3.2 Install LM393

Product Features

  • 【Wide – Application】Smart robot car is the most widely used in school for helping students to learn about the soldering project knowledge of mechanical structure, electronic basis skills, the principle of sensor, automatic control, soldering skill and so on
  • 【Easy Assembly】The operating principle is provided as above picture shown and we provide electronic manual for you. It’s much easier to assemble which is great for kids, begginers and hobbyist.
  • 【Its Principle】As the light reflectivity is difererent when the light is emitting on the white and black items. It uses the photoresistance resistance to tell the smart car is on the right way or not. Smart tracking car can discriminate the direction automatically that it can run freely along the black tracking line.
  • 【Design Your Runway】You can also use the 1.5~2.0 cm black electrical tape directly on the ground to design the complex runway. It would be even more fun!
  • 【English Manual】Contact us to get PDF manual or download the installation from drive.google.com/open?id=1kLlV2NlXQeXo56ItreQ1JlUParTRc-16
Volthaus Lab says:

A fun project kit for learning hobby electronics Length:: 0:18 Mins Really enjoyed putting this little line following robot car kit together. Instructions in English are available online The parts come loose in a plastic bag so step one can be identifying what are the parts are and where they go on the Printed Circuit Board (PCB)…

0
John Guy says:

As kits go this is one of the better ones I have tried in the recent past As kits go this is one of the better ones I have tried in the recent past. It is what I would call a fun build. It’s complex enough to make you think a little yet simple enough even a child could put it together. Even with the instructions in Chinese, it wasn’t very hard. It took me just under an hour and I wasn’t trying for a speed build.A big plus in my book was a socket to put the IC chip into. Many cheap kits would have you solder the IC chip directly into the PCB.

0
Enjuneer says:

Great for 12+ yo This is a great educational kit for young kids. Projects like these are a great way to teach/introduce basic electronics/robotics.I would say that you should supervise an inexperienced kid under the age of 12 (at the absolute earliest!) with this kit, since precision soldering is required. You may just want to assemble this one for them and have them observe. I haven’t fully assembled my kit yet, but I’ve gone over it thoroughly.This uses a very simple logic system to…

0

Write a comment

 *

 Join Our Newsletter
 Most Popular Products

Elemusi Cartoon Electronic Password Mini ATM Piggy Bank Cash... [Read More]

Clorox Disinfecting Wipes Variety Pack – 5 Pack, 390 C... [Read More]

Meeyou Girls Police Officer Costume, Cop Cutie Dress for Gir... [Read More]

Lysol Disinfectant Spray, Crisp Linen, 38oz (2X19oz)... [Read More]

OasisSpace Upright Walker – Tall Walker with 10″... [Read More]

 Products Just In

5 Pack: Big Boys Youth Clothing Knit Mesh Active Athletic Pe... [Read More]

The Children’s Place Big Boys’ Bootcut Jeans, Du... [Read More]

Levi’s Boys’ Big 514 Straight Fit Jeans, Covered... [Read More]

The Children’s Place Big Boys’ Pull-on Cargo Sho... [Read More]

Creativity for Kids Glow In The Dark Rock Painting Kit ̵... [Read More]